New USG policy control question
I was talking to zyxel support on some advice of setting up App Patrol. Misc question got us to me asking about how I saw the new Zyxel videos and how they had stuff setup with the UTM icons on...
View ArticleFirewall Rule - USG40W
Guys, This is driving me nuts, Im sure Ive done it correctly! Im trying to write a rule that allows, traffic from the WAN to access a server on the lan1 - the server is correctly configured as I can...
View ArticleVPN l2tp ipsec configured - How do I connect with my lan
Guys, I've managed to successfully setup a vpn with the help for excellent support from this forum. I can vpn in and use the internet from the wan of the USG, how do I connect with my nas (qnap) My lan...
View ArticleZyxel usg 100 Ooma DMZ
I have recently purchased an USG 100 and I would like to set up my Ooma Telo on the DMZ port. I have used the IP/MAC binding, and the 100 shows that has successfully bound. I have a link light, however...
View ArticleHow important is idp?
Hi guys, I'm jet having a think with regards to my network security, currently running 1 workstation, couple laptops, a Qnap NAS drive and various iPads etc.. Enabling the trial idp in the USG40W...
View Article"Network Risk" NAG SCREEN
I will switch on the "Network Risk" NAG SCREEN Warning. The system-default.conf don't bring it back. I think, I have read about a CLI command, but I can't find it.
View ArticleZywall USG 50 throughput gradually slows until rebooted
Hi, I have a Zywall USG 50 and apparently lack the necessary knowledge or skills to troubleshoot it. I have a 20/1 DSL connection which normally tests at about 16Mbps. I have a static IP address. Every...
View ArticleUSG50 firewall rules
Hi! I cannot for the life of me allow any incoming connection from WAN to LAN1 (or anything for that matter) on a zyxel USG50, it will always catch the default rule, and block it. notice Firewall Match...
View ArticleUSG 20 - NAT multiple LAN IPs to second WAN IP? (VPN Problem)
I'll start off with the question and add the details below for those that don't want to wade through it. Lets say that I have a block of WAN IPs: 100.1.1.0/29 and my LAN is 192.168.1.0/24. The WAN of...
View ArticleUSG50 L2TP/IPSEC VPN almost working (I think)
hello all, I am really close (I think) to getting my L2TP/IPSEC VPN working. I can connect using the Win7 client. I can't ping or see any computers on the network IPConfig shows: PPP Adapter...
View ArticleZywall 110 and Internet access while VPN'd
Read through as many related posts as I could find on here, but nothing jumping out at me as the solution. I've set up my Zywall 110 VPN following instructions cobbled together from here and...
View ArticleUSG110/210 questions
Do the new USGs have the Endpoint Security feature (EPS) that is in the USG100/200? This is where the USG checks the version of Windows for patches and antivirus before allowing on network? I really...
View ArticleZywall USG 20 and the Liftmaster 828LM Gateway
I'm trying to get a LiftMaster 828LM Internet Gateway working with my Zyxel 20, and for some reason it just repeats the DHCP cycle over and over - request IP, assign IP, confirm IP, wash, rinse,...
View ArticleThoughts on USG210 versus Watchguard XTM330
Yes, I know this is a Zyxel forum. That said, I know some here have also used other products. In looking at the new USG210, and in comparing to the XTM330, they are priced very similar. Yes, Watchguard...
View ArticleWriting a Rule that allows ISP multicast
Hi Guys, Im writing a rule that allows Mulitcast (224.0.0.1) from the ISP to my router, as its always coming up blocked. Can someone guide me through? Destination - Local Multicast 224.0.0.1 Source -...
View ArticleUSG 20: Site-Site & L2TP Enabled At The Same Time?
Hi Everyone, I have successfully set up a site-to-site connection and an L2TP connection. My goal is to link two offices and then be able to dial into the main office using the USG 20 for...
View ArticleARP table
Hi all, My client has a very wierd problem were their server hosting partner's ip-address is in the ARP-table causing all internal traffic to be routed to the gateway itself. How that got there from...
View ArticleUSG 20 Site-To-Site Tunnel Established but can't ping.
I'm in a bit of a bind. I can't for the life of me figure out why this isn't working. The title pretty much says it. I have a working site to site VPN tunnel using two USG 20 routers. Each has a static...
View ArticleZyxel Switches
Greetings- Anyone using the gs1910-48hp? I have one in my companies office and it seems pretty good for the slim price -- here's the dilemma I need to get a 48 port POE (for 10 VoIP) for a small...
View Article