I'm trying to get a LiftMaster 828LM Internet Gateway working with my Zyxel 20, and for some reason it just repeats the DHCP cycle over and over - request IP, assign IP, confirm IP, wash, rinse, repeat.
The Chamberlin support tech suggested that I increase UDP timeout to 180 seconds, which I have done, and make sure the firewall isn't blocking UDP Port 80. I fixed the timeout via the CLI, but I am not sure what needs to be changed to assure that UDP 80 is open through the firewall.
Has anyone used that Liftmaster gateway? Any thoughts on that UPD port 80?
Thanks!
↧
Zywall USG 20 and the Liftmaster 828LM Gateway
↧
Inside the ZyWALL 110
That's what the ZyWALL 110 looks inside. Can't stand the noise of the fan.
↧
↧
Zyxel p-600
I have this old Zyxel p-600 that i thought i'd try and put into bridge mode after seeing a couple of vids on youtube but i cant seem to get into the advance config menu.
I can access the router using the ip (192.168.1.1) but when i put in the password it doesnt give me the three options where i select advanced. Instead all i get is a status page for the router with no options to do anything except change the refresh interval.
Any ideas on how to get into the advanced menu? I'm connecting it to my laptop via an ethernet cable.
thanks
↧
Port scans from 53.
This is not necessarily related to Zyxel hardware but I would like to know what you guys think.
I have a USG50 and last couple of weeks I noticed increased port scanning from a bunch of IPs. The source seems a random IP but the source port is always 53. The destination is obviously my IP and random port.
Anyone have seen this? Here is a sample from log:
Date/Time Source Destination
2014-06-22 02:23:35 61.138.136.2:53 23.25.80.137:18435
2014-06-22 02:23:36 111.118.93.211:53 23.25.80.137:48234
2014-06-22 02:23:53 219.210.84.12:53 23.25.80.137:5162
2014-06-22 02:24:07 217.157.193.50:53 23.25.80.137:5162
2014-06-22 02:24:13 212.94.179.180:53 23.25.80.137:51297
2014-06-22 02:26:08 61.25.65.142:53 23.25.80.137:59465
2014-06-22 02:26:12 98.112.117.237:53 23.25.80.137:53339
2014-06-22 02:26:14 112.140.251.144:53 23.25.80.137:4141
↧
USG 60 - MRTG
I watch WAN traffic using MRTG since Zyxel 334 times without any problems. Now with USG 60 it works or works not.
The first picture shows the constant TV-stream from 11:00 up to 23:30. The log goes to zero at 13:30. At 14:30 I reboot the USG 60 and the log works for another 3 1/2 hours. Additional the shown up-time has an offset of 2 hours.
The intern USG 60 WAN traffic log (second picture) from the reboot at 14.30 up to 23:30 is not typical for a constant stream and no great help.
Regarding MRTG it looks like, that something runs full.
The MRTG version is 2.9.29. Has anybody an idea?
↧
↧
L2TP VPN over Dual WAN
Anyone know if zywall can set L2TP VPN over 2 wan if one of the wan is down? I can only choose one configuration from VPN connection profile on the L2TP VPN setting.
↧
Switch off specific UTM new USG engines, they made it very inconvenant
OK here is what you have to do. Configuration>> Security Policy >>Policy control. Click on LAN1 that has the UTM AV IDS and other funny looking UTM icon that are on the far right. Double click and a window should come up, scroll down in that window to get this.
The picture is from Zyxel own demo gui page.
https://demousg110.zyxel.com/
I would think you would want to enable the UTM engines from Wan to LAN1, that is not enabled in this picture. User name:: demo Password:: demouser
.
↧
USG 50 Multiple xboxes
I got a USG-50 a couple months ago and really like it. We have a home office and after setting everything up my network is humming along nicely except for my xbox 360's I have a couple kids and they play in the game room while I am watching something on one of the video apps in another room or play online with games that are only one player on the same console. Everything was fine when we were just using the networking on a wireless AP but ended up with too many devices and things were getting bad. Of course the wireless AP was doing upnp and I only have the option to forward the xbox ports to one IP on the USG50.
I dropped one of the xboxes in the DMZ to isolate it and it runs fine. If I want to use the other I have to go and swap out the cable and of course can't do both at the same time since the DMZ is just one IP. Just an FYI the cable modem from our ISP is in bridge mode.
What I wanted to do was drop something like my old Asus Darknight wireless router onto the DMZ through its WAN port (just picked up a a Netgear Nighthawk). Turn of the wireless and go wired so I don't have to mess with channels and leave something hooked into the DMZ unprotected. Assign static ip's to the xboxes and let upnp do it's stuff isolated from the rest of the network. It will let the xobes talk to each other to play local and let them use port triggering to talk to xbox live.
Am I going to run into a problem with this? I know it sounds crazy to do all this but the kids like to game and they are at the age where it's fun to play with/against them.
↧
USG50 stats don't reset
I have the box checked to email the stats each night and then reset. The email shows up, but the stats don't reset. After a seemingly random period of days (a week or so), they do reset, but that's not helpful. I've unchecked the box and applied, then re-checked and applied. No joy.
Anyone else with this issue or a solution? I can call support but past experience indicates that they'll ask me to reset it to defaults and reconfigure and that's not an option- it's remotely located an airplane flight away.
↧
↧
Zywall 110 and SSL
Hi, recently I bought from Godaddy UCC SSL cert. that was meant for Lync Server. Since there was a place for 2 more SANs (10 in total) I added ssl.domain.com.
Now on the Zywall 110 I've configured SSL VPN.
Unfortunately I have other websites behind zywall, so I NAT-ed 443 traffic to pass through the zywall and go to the IIS ARR. There it is proxied to appropriate server. On the ARR I configured, among the other farms, SSL webfarm, and rerouted traffic back to Zywall. So technically what I wanted to do is:
1. traffic comes to the Zywall, and because of the NAT rule it is routed to ARR
2. ARR check URL rewrite rule, and see that it is intended for SSL.domain.com and route traffic to Zywall.
3. Users are able to log in to SSL VPN.
But for SSL VPN I need certificate.
Since I have UCC cert. only one cert is installed on ARR. On the other hand I need to install that certificate on Zywall.
What I tried:
I tried to install intermediate cert. to trusted certificates, and the certificate I exported from ARR to My Certificates. Import process was successful. Then for WWW I wanted to use certificate I imported and voila, I got unresponsive Zywall! Even though I have on purpose unchecked route HTTP to HTTPS (to be able to access it if the certificate is bad) I was not able to access over HTTP also!!!! So I needed to reset conf to factory settings and read the old one from the backup.
Can someone please help me to install certificate?
↧
USG40W -where is the wlan settings?
Hi,
Just taken delivery of the new USG40w, its be configured correctly and updated to the latest 4.10 firmware.
For the life of me I can not find the wlan settings? - strangely the manual doesn't mention wlan settings either, I know I have the correct model as it comes with the wifi aerials.
The USG20w had the wlan settings in the tab - configuration/network/interface/wlan the USG40w seems to have omitted this?
Can anyone help?
↧
USG40W DDNS issues
Hi,
Im having a problem in trying to get my ddns to sync, its been unsuccessful at present - Ive used both no-ip and dyn.
Im using pppoe with a dynamic ip from isp.
When look in the logs, i see the following error message:
(name of ddns) has failed because the WAN interface was inactivated
(name of ddns) has failed because IP address of WAN interface wan1 was empty
Any ideas?
↧
Syntax to set DHCP option 66 on ZyWALL 5?
Need to set this so some remote VoIP phones can find their boot server.
I know this works for lease time (and isn't in the onboard help):
ip dhcp enif0 server lease
I'm thinking there must be some syntax to set other DHCP options.
↧
↧
Zyxel USG50 reboot failure with USB drive
I have a USG50 with a USB drive mounted to collect log files. I have had several occurrences where a reboot will cause the device to freeze (SYS LED keeps flashing for over 30 min). Power cycling the router does not resolve the issue until I remove the USB drive after which it will reboot normally. Logs don't show any abnormalities but they don't record early boot events. Any ideas?
↧
Newbie Zywall110 Console Questions.
I have my Zywall 110 up and running, but have had problems with Firmware update, so need to access the console port.
Problem is I get no response using Telnet (Host Name 192.168.1.1, port 23) or SSH (Host Name 192.168.1.1, port 22).
Both Telnet and SSH are "enabled" in the System Config pages.
Port is configured for 115200, 8, 1, none & none, as per instructions.
I am using a "generic" USB RS232 adaptor cable, which tests OK with pins 2 & 3 of the DB9 shorted.
Q1. Should I be using a "Cisco" pinned cable or a standard pinned cable?
Q2. Is the cable required to be "crossed" or "straight"?
Q3 I assume the default Host Name for connecting is 192.168.1.1 - anyone know if it should be different?
Cheers!
↧
NAT DNS traffic usg 100
Hi all,
I am looking for a way to reroute the traffic from my cromecast to another address.
Cromecast standard uses 8.8.8.8 and 8.8.4.4, i want those adresses to be routed to another DNS.
This should be possible i think. However i cannot get this working.
Does anyone have suggestions?
Thanks!
Barry
↧
Zywall USG100 configuration for IPTV
Hello everyone,
I have an Zywall USG100 that i would like to use for sending IPTV traffic to my digibox on the network. My ISP is "Telenet" (Belgium) and they are not using any VLAN on the IPTV network.
My WAN interface receives the public IP adres from the modem and i should need to get the public IP to my digibox so i could get interactive TV (they do MAC adres control).
The internal LAN (interface1) has a DHCP server on the 192.168.1.X network and i made a VLAN2 for a Guest Wifi network in the 192.168.20.X range also on interface1.
There are 2 switches in the network that handle all the traffic (also for VLAN), a HP Procurve 1800-24G and a HP Procurve 1810G-8.
At this moment i made a VLAN3 that i want to use for the IPTV traffic, but i don't know how to configure the Zywall so that the public IP come's on the VLAN3. After the VLAN3 receives the public IP i need to configure my switches so that the port where my digibox will be connected is also on VLAN3. But VLAN3 will leave the Zywall trough interface1, just like the rest of my data.
Could someone give me some help on how i get the configuration right? I googled this but i can't find any good workarounds.
Here is a link to my dropbox folder where you can find the setup and some screenshot of the zywall config. If there are any question just ask, my knowledge isn't enough to configure this.
https://www.dropbox.com/sh/obk5763p6wwz6a0/AACEP-bKeAolT-KgI-WUTvvMa
Thanks in advance
↧
↧
VPN settings for USG40W
Hi there,
Followed Brano's excellent tutorial on setting up a L2TP IPSec
http://www.dslreports.com/forum/r26985207-L2TP-VPN-on-USG-quick-how-to
Ive manged to get it a client/iphone to connect the the USG, my problem is how do I configure the VPN so that the client uses internet from the wan of the USG?
The Behaviour of the iphone is that it continues to use the internet from the mobile network.
The Behaviour of windows, is that it stops/blocks Internet from the WWAN
Ive paid attention to the following:
6) Create required firewall rules
To access your LAN
(If you want to allow your L2TP to access LAN and internet change LAN1 in below to ANY)
↧
2 Vlans on one port Zyxel USG 60
Hey forum people!
I google this forum by looking info how to set up 2 vlans on same port for zyxel usg 60 router, there is not much info about it, but as setting are quite similar to usg 20/50/100 maybe anyone can advise on the steps I have to go through? I read some threads and I see people here have quite knowledge how to set up those routers.
For the begining I am not a big network expert and my requirements are to divide 2 groups of users into separate networks, unfortunately because of poor physical network wiring it is not possible to separate vlans with the manageable switch or on 2 different ports :(
Configuration should look something like this:
http://www.manualslib.com/manual/363461/Zyxel-Communications-Zywall-Usg-20.html?page=264
Also I tried creating VLANs but for the moment I can't manage them to work, it looks that internet is working on one vlan, but not on the other. In addition, I am not sure if that even possible, but it would be great to have a dhcp server active on one of the vlans, so far have not succeeded on getting any IPs from router. Users on the other vlan will get dhcp from the server or will be with static IPs.
Any help would be much appreciated :)
↧
USG 50 - with Layer 3 Dell 6224
Having issues with a USG 50 communicating with VLANs configured on a Dell 6224
USG has the VLAN's created and assigned to LAN1 Zone - i was told by Zyxel this is all that's needed. I cannot ping from VLAN to Zyxel gateway IP or vice versa.
Do i need a policy route for the LAN1-VLANx/group ?
↧